BENQ MP610 MANUAL PDF
|Published (Last):||4 November 2010|
|PDF File Size:||19.16 Mb|
|ePub File Size:||13.68 Mb|
|Price:||Free* [*Free Regsitration Required]|
Copyright Copyright by Mp60 Corporation. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.
Calculation of lamp hour Important safety instructions Your BenQ projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.
Safety Instructions Manuwl lamp becomes extremely hot henq operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement. Do not operate lamps beyond the rated lamp life. Excessive operation of mabual beyond the rated life could cause them to break on rare occasions. Safety Instructions Continued Do not place this projector in any of the following environments.
Allow at least 50 cm clearance from walls and free flow of air around the projector. Liquids spilled into the projector may cause it to fail. Important safety instructions This product is capable of displaying inverted images for ceiling mount installation. Introduction Projector features The projector henq high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use.
The projector offers the following features: Shipping contents The projector is shipped with the cables required for connection to a PC and to video equipment. Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Power indicator light Refer to Lights up or flashes when the projector is under operation. Remote control Power Refer to “Start up” on page 21 mation. Turns the projector on or off.
Freeze The image is frozen when Freeze is pressed. An icon ” right corner of the screen. To release the function, press Freeze again. Infra-Red IR remote control sensors are located on the front and the back of the projector.
Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.
BenQ has provided a table of 4: There are two dimensions to consider, the perpendicular If you place the projector in a different position to that recommendedyou will have to tilt it down or up to center the image on the screen. In these situations, some image distortion will occur. Connecting a computer or monitor Connecting a computer The projector provides a VGA input socket that allows you to connect it to a laptop or desktop computer. Additionally, you can also connect the projector to a computer via the USB cable so you can perform paging operations of the application on the PC or notebook.
If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the RGB signal output socket on the projector to an external monitor with a VGA cable following the instructions below The method you choose will most likely depend upon the availability of matching terminals on both the Also check that the signal cables have been connected correctly.
The final connection path should be like that shown in the following diagram: The search will continue until an input source signal is detected. You can also press Source on the projector or remote control to select your desired input signal. Press and hold Right4 for 5 seconds. The projector will display a coded number on the screen.
Seek help from the local BenQ service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.
Manual – BenQ MP Projector
Press Down 6 to cancel the set-up and return to the on-screen menu. Adjusting the height The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector Press 6 Menu on the projector or Menu on the remote control. However, it can only display one at a time. To cycle through the available input sources, press the Source button on the projector control panel or the remote control.
The selected source name will display at the center of the screen for 3 seconds after each button press. Freezing the image Press the Freeze button on the remote control to freeze the image. Menu operation Menu system Please note that the on-screen display OSD menus vary according to the signal type selected. Functions available when receiving different signal types Using the menus The projector is equipped with on-screen display OSD menus for making various adjustments and settings.
There are 17 different menu languages. Refer to page more details. The following example describes the adjustment of the keystone. Press 6 Menu on the projector or Menu on the remote control to turn the on- screen menu on.
Maximizes the brightness of the projected image. This mode is mp6100 for environments where extra-high brightness is manuall, such as using the projector in well lit rooms.
Is designed for presentations. The brightness is emphasized in this mode to match PC and notebook coloring. For input signals with lower resolutions, the projected image will display smaller than if resized to full screen. You could adjust the zoom setting or move the projector towards the screen to increase the image size if necessary.
You may also need to refocus the projector after making these adjustments.
BenQ MP610 Projector
Cooling off second duration to approximately 30 seconds. This is a selectable function. Selecting On limits use of the projector to only those who know the correct password. When the function is activated for the first time, you have to set a password for it. For more information, refer to is set and this function is selected, the projector is password-protected.
Allows you to select which logo screen will display during projector start- Splash up. Three modes are available: Default BenQ logoblack screen or blue Screen screen. BenQ logo for more information.
Connection – Benq MP User Manual – Page 21 of 55 |
A confirmation message displays. Next time you turn on the projector, it will show a message pictured below High Manial as a reminder during the start-up. Information menu This menu shows you the current operating status of the projector. Some picture adjustments are available only when certain input sources are in use. Unavailable adjustments are not shown on the screen.
Maintenance Care of the projector Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing. The Lamp indicator light and Temperature warning light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes.
If the Lamp or Temp indicator manul lights up after turning the power back on, manal contact your dealer. To reduce the risk mp6610 electrical shock, always turn the projector off and disconnect the power cord before changing the lamp. If you touch the optical components inside, it could cause color unevenness and distortion of the mabual images. When the Temperature warning light is on, it is warning you of the following possible problems: The internal temperature is too high.
The fans are not working. Turn the projector off and contact qualified service personnel for further help. For more detailed information, please refer to Maintenance “Indicators” on page The Power indicator light is flashing during powering up.
The projector is under normal operation. The projector needs 90 seconds to cool down as it was abnormally shut down without the normal cooling down process. Or Mwnual projector needs to cool for 90 seconds after the power is turned off. Thermal events Maintenance The projector has shutdown automatically.